- Behringer Windows 10 Drivers
- Behringer Others Driver Download For Windows 10
- Behringer Others Driver Download For Windows 10 64-bit
- Behringer Others Driver Download For Windows 10 64
04-12-2020, 11:55 PM
I bought the Behringer UM2 interface, since I really only needed the one port for input from my Roland TD-15, which I run thru a Mackie 1402 (along with a condenser mic for chat) and into the UM2. I was dismayed when I found out the driver I had to use was ASIO4ALL, as that is what JamKazam says NOT to use, but it's what Behringer pointed me to, so I downloaded an installed it - see attachment for latest settings used. BTW running on Lenovo laptop w/ Windows 10.
On my numerous attempts to setup my Audio Gear in JamKazam, I have never been able to get it to work cleanly when I select ASIO4ALL. on initial setup, it can't determine latency and I have to go to loopback Test page, where (when the test works at all) latency is around 3-4ms, but I/O usually fails test and I can't proceed. Occasionally, for reasons I do NOT understand, it does pass the I/O part too and I am able to add that audio gear setup and then open a solo session. However, the audio in the solo session is either really bad, with lots of noise and odd sounds, plus I see lots of output jitter - but the latency is good (under 5), OR the sound is very intermittent, meaning I can tap one of the drums and only 1 note out ten come thru. (Direct Monior is OFF on interface). I also frequently hear a faint popping sound during setup.
I have disabled the on-oard audio devices, so that only the USB Codec device (which is the interface) is active and set both input and output sampling to 48K Hz (have also tried 41K).
I have alternatively been able to setup my audio by selecting USB Codec using the default WMD driver and jam, but my internal latency is ALWAYS 20ms, so that is not ideal.
I am debating tossing the Berhinger UM2 and buying the Focusrite Scarlett 2i2 3rd Gen, but I have also seen some posts where that seems to have problems on Windows 10 and I think I might have seen one where it said that had to use ASIO4ALL too, in which case I am not buying it, if that is true.
Wondering if anyone has been able to get ASIO4ALL working with any Berhinger interface, especially the UM2? Or is there another ASIO driver I can use?
On my numerous attempts to setup my Audio Gear in JamKazam, I have never been able to get it to work cleanly when I select ASIO4ALL. on initial setup, it can't determine latency and I have to go to loopback Test page, where (when the test works at all) latency is around 3-4ms, but I/O usually fails test and I can't proceed. Occasionally, for reasons I do NOT understand, it does pass the I/O part too and I am able to add that audio gear setup and then open a solo session. However, the audio in the solo session is either really bad, with lots of noise and odd sounds, plus I see lots of output jitter - but the latency is good (under 5), OR the sound is very intermittent, meaning I can tap one of the drums and only 1 note out ten come thru. (Direct Monior is OFF on interface). I also frequently hear a faint popping sound during setup.
I have disabled the on-oard audio devices, so that only the USB Codec device (which is the interface) is active and set both input and output sampling to 48K Hz (have also tried 41K).
I have alternatively been able to setup my audio by selecting USB Codec using the default WMD driver and jam, but my internal latency is ALWAYS 20ms, so that is not ideal.
I am debating tossing the Berhinger UM2 and buying the Focusrite Scarlett 2i2 3rd Gen, but I have also seen some posts where that seems to have problems on Windows 10 and I think I might have seen one where it said that had to use ASIO4ALL too, in which case I am not buying it, if that is true.
Wondering if anyone has been able to get ASIO4ALL working with any Berhinger interface, especially the UM2? Or is there another ASIO driver I can use?
Behringer Windows 10 Drivers
Behringer Others Driver Download For Windows 10
1) Download and install Driver Easy. 2) Run Driver Easy and click the Scan Now button. Driver Easy will then scan your computer and detect any problem drivers. 3) Click the Update button next to the audio driver to automatically download the correct version of that driver, then you can manually install it (you can do this with the FREE version).
Behringer Others Driver Download For Windows 10 64-bit
Behringer Others Driver Download For Windows 10 64
- There are some users who have driver issues and other software bugs, but after updating the main software, they umc204hdd able to fix the problem and enjoy its features. If you’re thinking of grabbing one of these, I strongly recommend that you do so. Behringer U-Phoria UMC204HD.
- Go to the Download Windows 10 page and click the 'Using the tool to create installation media' link to see detailed instructions. The quick steps are here: Plug in the USB thumb drive you plan to use as your Windows 10 installer. Click the Download tool now button to download the file MediaCreationTool.exe. Locate the downloaded program.